Metal Materials
EN 1.3343 High Speed Steel: Properties, Manufacturing for Precision Cutting
When your machining operations involve high-speed cutting of hard materials—stainless steel, alloy steel, or heat-resistant alloys like Inconel—you need a tool steel that maintains its cutting edge under extreme heat and pressure. EN 1.3343 high speed steel is engineered for these demanding conditions.
Key takeaways
- EN 1.3343 achieves its properties through a carefully balanced chemistry that includes significant amounts of tungsten, molybdenum, vanadium, and cobalt.
- This material is specified for cutting tools that operate at high speeds and temperatures, particularly when machining hard materials.
- Producing EN 1.3343 requires precise control over chemistry, melting, forging, and heat treatment to achieve the desired carbide structure and properties.
- Understanding the trade-offs between EN 1.3343 and alternative materials helps in making an informed selection.
What Makes EN 1.3343 a High-Performance Tool Steel?
EN 1.3343 achieves its properties through a carefully balanced chemistry that includes significant amounts of tungsten, molybdenum, vanadium, and cobalt. These elements form hard carbides that resist wear and allow the steel to maintain hardness at temperatures up to 650°C.
The Chemistry Behind the Performance
The chemical composition of EN 1.3343 is designed to create a high density of hard carbides that resist abrasion and maintain strength at high temperatures.
| Element | Content Range (%) | Why It Matters |
|---|---|---|
| Carbon (C) | 0.80 – 0.90 | Forms hard carbides with tungsten, molybdenum, and vanadium. Provides wear resistance. |
| Tungsten (W) | 5.50 – 6.75 | A key element for red hardness. Forms carbides that retain strength at 600°C+. |
| Molybdenum (Mo) | 4.50 – 5.50 | Works with tungsten to enhance red hardness and reduce brittleness. |
| Vanadium (V) | 1.70 – 2.20 | Forms ultra-hard vanadium carbides. Improves edge retention and wear resistance. |
| Cobalt (Co) | 4.50 – 5.50 | Further boosts red hardness and high-temperature stability. |
| Chromium (Cr) | 3.80 – 4.50 | Supports carbide formation and improves hardenability. |
| Manganese (Mn) | 0.15 – 0.40 | Improves hardenability and reduces brittleness. |
| Silicon (Si) | 0.15 – 0.40 | Enhances strength and oxidation resistance at high temperatures. |
| Sulfur (S) / Phosphorus (P) | ≤ 0.030 | Kept low to prevent brittleness and maintain toughness. |
Key Insight: The combination of tungsten (5.50–6.75%) and cobalt (4.50–5.50%) is what distinguishes EN 1.3343 from standard high speed steels. This allows the material to retain approximately 90% of its hardness at 600°C, enabling high-speed cutting operations that would soften lower-grade tool steels.
Mechanical Properties That Matter
EN 1.3343’s mechanical properties are optimized for cutting tools. The material is heat-treated to achieve high hardness while maintaining enough toughness to resist chipping.
| Property | Typical Value | Significance |
|---|---|---|
| Hardness | 63 – 66 HRC | Ultra-high hardness ensures excellent edge retention for milling cutters, drills, and broaches. |
| Red Hardness | 90% of hardness retained at 600°C | Allows cutting at high speeds without softening. Critical for high-speed machining. |
| Tensile Strength | ≥ 2400 MPa | Handles high cutting forces without breaking. |
| Yield Strength | ≥ 2000 MPa | Resists permanent deformation, maintaining cutting geometry. |
| Impact Toughness | ≥ 12 J | Moderate toughness helps avoid brittle fracture during light shock loading. |
| Fatigue Strength | ~900 MPa | Resists failure from repeated cutting cycles in high-volume operations. |
| Elongation | ≤ 5% | Low ductility, typical for high-hardness tool steels. |
Case Study: A German machine shop was using standard HSS milling cutters for machining alloy steel parts. The cutters wore out after 500 parts. They switched to EN 1.3343 cutters coated with TiAlN. Tool life increased to 2,000 parts—a 300% improvement. Machining speed increased from 25 to 40 meters per minute, reducing production time significantly.
Where Does EN 1.3343 Deliver the Most Value?
This material is specified for cutting tools that operate at high speeds and temperatures, particularly when machining hard materials.
Cutting Tools for Hard Metals
EN 1.3343 is widely used for cutting tools that machine stainless steel, alloy steel, cast iron, and heat-resistant alloys.
- Milling cutters: End mills and face mills for machining hard materials.
- Turning tools: Lathe tools for turning hardened steels and stainless alloys.
- Drills: Twist drills for drilling holes in tough materials.
- Reamers: Precision reamers for achieving tight tolerances in hardened materials.
Case Study: A Chinese aerospace manufacturer was drilling Inconel parts with standard HSS drills. The drills lasted only 20 holes before failure. They switched to EN 1.3343 drills with TiAlN coating. Drill life increased to 80 holes per tool—a 300% improvement—reducing tool change downtime and lowering production costs.
Broaches and Gear Cutting Tools
Broaching and gear cutting require tools that maintain sharp cutting edges through hundreds or thousands of cuts.
- Broaches: Internal and external broaches for creating splines, keyways, and complex shapes.
- Hob cutters: Gear hobs for manufacturing automotive and industrial gears.
- Shaping tools: Tools for cutting gear teeth and other precision features.
Case Study: A U.S. automotive supplier was using standard HSS broaches for cutting gear splines. The broaches lasted 5,000 parts before requiring sharpening. They switched to EN 1.3343 broaches. Broach life increased to 15,000 parts—a 200% improvement—reducing tool change downtime and sharpening costs.
High-Speed Machining Applications
EN 1.3343 is ideal for applications where cutting speeds are high and tool temperatures are elevated.
- High-speed milling: Machining at speeds above 30 meters per minute in steel.
- Hard turning: Turning hardened steels up to HRC 45.
- Heat-resistant alloy machining: Cutting Inconel, titanium, and other difficult-to-machine alloys.
How Is EN 1.3343 Manufactured and Processed?
Producing EN 1.3343 requires precise control over chemistry, melting, forging, and heat treatment to achieve the desired carbide structure and properties.
Melting and Casting
EN 1.3343 is typically melted in an electric arc furnace (EAF) or induction furnace at 1,550–1,650°C. The high-value elements such as tungsten and cobalt are added during melting to ensure uniform distribution. After melting, the steel is cast into ingots with slow cooling (10–20°C per hour) to prevent carbide segregation.
Forging and Rolling
Ingots are heated to 1,100–1,180°C and forged into tool blanks. Forging breaks up large carbides that form during casting, improving tool strength and toughness. After forging, the material is rolled or further shaped as needed.
Heat Treatment: The Critical Step
Heat treatment is essential for achieving EN 1.3343’s high hardness and red hardness.
- Annealing: Heat to 850–900°C, hold for 2–4 hours, then cool slowly. Softens the steel to HRC 24–28 for machining.
- Preheating: Heat to 800–850°C, hold for 1 hour. Prepares the steel for austenitizing.
- Austenitizing: Heat to 1,200–1,240°C, hold for 15–30 minutes. This critical step dissolves carbides into the matrix.
- Quenching: Cool rapidly in oil or air (depending on tool size). Hardens the steel to HRC 64–67.
- Tempering: Reheat to 540–580°C, hold for 1–2 hours, then cool. Repeat 2–3 times. This reduces brittleness while maintaining high hardness (HRC 63–66).
Machining and Finishing
Most shaping of EN 1.3343 tools is done in the annealed condition. After heat treatment, precision grinding is used to achieve sharp cutting edges and tight tolerances.
- Machining: In the annealed condition, EN 1.3343 can be machined with carbide tools.
- Grinding: After heat treatment, use diamond or CBN wheels for precision grinding.
- Surface treatment: TiAlN (titanium aluminum nitride) or TiN (titanium nitride) coatings can extend tool life by 50–100% by reducing friction and providing additional heat resistance.
How Does EN 1.3343 Compare to Other Materials?
Understanding the trade-offs between EN 1.3343 and alternative materials helps in making an informed selection.
| Material | Hardness (HRC) | Red Hardness (600°C) | Relative Cost | Best For |
|---|---|---|---|---|
| EN 1.3343 | 63 – 66 | Excellent (90% retained) | 100% | High-speed cutting of hard metals |
| Standard HSS (M2) | 60 – 63 | Good (80% retained) | 60% | General cutting of mild steel |
| Carbide | 85 – 90 (HV) | Excellent | 300% | Ultra-high-speed cutting, high-volume production |
| Ceramic Tools | 90 – 95 (HV) | Outstanding | 500% | Machining super-alloys, very high speeds |
| Carbon Steel | 55 – 60 | Poor | 20% | Low-speed cutting of soft materials |
Key Insights:
- Compared to standard HSS (M2), EN 1.3343 offers significantly higher red hardness and wear resistance for a 60–70% cost premium. For high-speed cutting of hard materials, this upgrade pays for itself through longer tool life and higher productivity.
- Compared to carbide, EN 1.3343 is substantially less expensive and more impact-resistant. Carbide is the choice for very high-speed, high-volume production; EN 1.3343 is preferred for applications requiring moderate toughness and lower tool cost.
- Compared to carbon steel, EN 1.3343 is far superior in every performance metric. Carbon steel tools are only suitable for low-speed cutting of soft materials.
How to write a spec that gets priced correctly
A drawing is a contract. If it leaves a number open, the shop fills that number in with its own default. The default is rarely the one you had in mind. Put these five lines on every RFQ and most of the back-and-forth disappears before it starts.
- Alloy designation and the standard behind it
- Temper or heat treatment condition
- Mechanical properties you actually need
- Mill certificate and traceability requirement
- Finish and the faces it applies to
The point is not paperwork. Each line removes a decision the shop would otherwise make for you. A complete RFQ comes back priced. An incomplete one comes back guessed.
What actually drives the price
Buyers usually push on material because it is the line they can see. In practice the material is rarely the biggest number on a quote. These five lines decide most of it:
- alloy grade and mill availability
- stock size versus finished size
- heat treatment and testing
- machinability
- certification
Ask for the quote split by line. A supplier who cannot break it down is guessing, and you will pay for the guess. The line you can usually renegotiate is the tolerance band, not the raw material.
Problems you will meet, and the fix
Every process has a failure mode it prefers. The same four show up again and again on this kind of work, and none of them are mysteries once you know what to look for.
- Substituting a similar grade without telling anyone
- Hardness that varies across a single bar
- Corrosion in a weld heat-affected zone
- Distortion after heat treatment on a thin part
Catch the fault on the first part, not the hundredth. A first-article check costs an hour. A bad batch costs the whole order. Write the check into the purchase order so nobody has to remember it.
What to check on the first article
The first article is the cheapest inspection you will ever buy. Use it properly and the rest of the run becomes boring, which is exactly what you want.
- Every dimension on the drawing, with the measured value written beside it.
- The material certificate, matched to the heat or lot number on the parts.
- The finish against the sample you approved, under the same light.
- Fit against the mating part, assembled rather than measured.
- Packaging, because parts that arrive damaged were never in tolerance.
Check in this order: datums, then mating features, then cosmetic faces. If the datums are wrong, every number after them is noise. Keep the report on file. When a problem shows up in month six, that document is the only thing that tells you what changed.
How to compare two quotes fairly
Two numbers are not comparable unless the scope matches. Line them up before you decide, because a low number with three gaps is not a low number.
Same drawing, same material, same finish, same inspection. Anything else is a different job wearing the same part number. Then look at what each quote leaves out. Freight, packaging, certificates and tooling are the usual gaps.
Ask each supplier to state their assumptions in writing. The one who does is usually the one who has run the process before.
Scaling from one part to a batch
The first part teaches you the process. The hundredth teaches you the process cost.
Watch three things as volume grows: setup amortisation, tool wear, and how much hand work the finish still needs. If the unit price barely moves between ten and a hundred, the cost sits in material or in hand work, not in setup. Ask which, because only one of them is negotiable.
Lead time behaves the same way. A one-off is scheduled around other jobs. A repeat order is scheduled around your forecast. Give the shop a forecast and the lead time gets shorter, not longer.
What About Coatings?
Surface coatings can significantly extend the life of EN 1.3343 tools.
- TiAlN (titanium aluminum nitride): Best for high-speed cutting of steel and stainless steel. Resists temperatures up to 800°C and reduces friction. Ideal for milling and drilling applications.
- TiCN (titanium carbonitride): Good for machining aluminum and non-ferrous materials. Prevents material buildup on the cutting edge.
- TiN (titanium nitride): A general-purpose coating that provides moderate wear resistance and reduces friction.
Case Study: The German machine shop mentioned earlier used TiAlN-coated EN 1.3343 cutters. The coating reduced friction at the cutting edge, allowing higher cutting speeds and further extending tool life beyond the base material’s capabilities.
EN 1.3343 high speed steel is a premium tool steel for demanding cutting applications. Its tungsten, molybdenum, vanadium, and cobalt content provides exceptional red hardness, allowing tools to maintain their cutting edge at temperatures up to 650°C. For high-speed machining of stainless steel, alloy steel, and heat-resistant alloys, EN 1.3343 delivers longer tool life, higher cutting speeds, and better surface finishes than standard HSS. While it costs more than conventional HSS, its performance in demanding applications makes it a cost-effective choice for manufacturers who prioritize productivity and quality.
FAQ About EN 1.3343 High Speed Steel
Can EN 1.3343 be used for machining non-metallic materials such as plastics or wood?
Yes, technically it can, but it is overspecified for these applications. EN 1.3343’s high hardness and red hardness are designed for metal cutting. For plastics and wood, standard HSS or carbon steel tools are sufficient and significantly less expensive.
What is the best coating for EN 1.3343 tools?
For most applications, TiAlN (titanium aluminum nitride) is the best choice. It resists high temperatures up to 800°C and reduces friction, making it ideal for high-speed cutting of steel and stainless steel. For machining aluminum, use TiCN (titanium carbonitride) to prevent material buildup on the cutting edge.
Is EN 1.3343 more expensive than standard HSS?
Yes. EN 1.3343 costs approximately 60–70% more than standard HSS such as EN 1.3340 (M2) due to its cobalt and tungsten content. However, EN 1.3343 tools typically last 2–3 times longer and allow higher cutting speeds, making them more cost-effective in high-volume operations.
What heat treatment is recommended for EN 1.3343 tools?
The standard cycle is: anneal at 850–900°C, preheat at 800–850°C, austenitize at 1,200–1,240°C, quench in oil or air, and temper at 540–580°C with 2–3 cycles. This achieves 63–66 HRC with good toughness.
Our solution for EN 1.3343 High Speed Steel
YiguProto runs metal sourcing and machining in house, from a single prototype to a production batch. We quote the process, the material and the finish as separate lines, so you can see where the money goes instead of arguing with one number.
Send a STEP file or a drawing and you get a DFM report in one to two business days. It flags the features that add cost and the features that will not hold tolerance on the process you picked.
Every order ships with an inspection report on the features you call out. If a part misses, we make it again. Ready to price a part? Start with a free quote and DFM review, or read more about our metal sourcing and machining. You can also talk to an engineer before you commit to a drawing.
FAQ about EN 1.3343 High Speed Steel
Does the process work for prototypes as well as production?
Yes, and that is usually the point. Running the prototype on the production process removes a whole class of surprises, because the part you test is made the same way as the part you sell.
What tolerance can you hold on EN 1.3343 High Speed Steel?
The working default is ±0.05 mm on machined features, ±0.1 mm on formed ones. Tighter than that the process changes and so does the price, because every step tighter adds inspection time. Call out only the faces that mate with something else and leave the rest on the general tolerance.
What should I check before approving the parts?
Datums first, then the features that mate, then the cosmetic faces. Ask for a dimensional report, a material certificate and a finish sample. A part can be inside every tolerance and still not fit, so assemble one before you sign.
What files do you need in order to quote?
A STEP file plus a PDF drawing that carries the same revision letter. The model carries the geometry and the drawing carries the intent. When the two disagree, the shop picks one, and it is never the one you meant.
How much does EN 1.3343 High Speed Steel cost?
Price comes from five lines: material, machine or tool time, setup, finishing and inspection. The material itself is usually the smallest of them. Send a drawing and we will split the quote so you can see which line is doing the damage.
What is the lead time for EN 1.3343 High Speed Steel?
Expect 5 to 12 business days depending on mill stock. Tooling, material stock and the finishing queue all move that number, so we confirm the date in writing before the run starts rather than after.
The short version
EN 1.3343 High Speed Steel rewards the buyer who reads the data sheet and the drawing together. Pick the option for the property that matters, not for the price per kilo.
Tighten only what mates. Test a sample before the run. Then let the process do the rest.